曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Reference Description
SPL-1726 Clamp Set - Trailing Edge Flap Torque Tube
(Part #: C27022-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
D. Location Zones
Zone Area
561 Left Wing - Rear Spar to Trailing Edge, Outboard Of Inboard Flap,
Inboard of Fixed Trailing Edge
567 Left Wing - Outboard Flap
661 Right Wing - Rear Spar to Trailing Edge, Outboard of Inboard Flap,
Inboard of Fixed Trailing Edge
667 Right Wing - Outboard Flap
E. Prepare for the Removal
SUBTASK 27-51-58-860-001
(1) Extend the trailing edge flaps to the 40-unit position. To extend them, do this task: Extend the
Trailing Edge Flaps, TASK 27-51-00-860-803.
SUBTASK 27-51-58-040-001
(2) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 401
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
F. Outboard Wing Flap Torque Tube Removal
SUBTASK 27-51-58-480-001
(1) Install the clamp set, SPL-1726 on the torque tubes inboard and outboard of the applicable
torque tube (Figure 402):
NOTE: The clamp set can be used to stop inadvertent movement of the flap drive system while
the torque tubes are disconnected. If the flap drive system moves, then it will be
necessary to do the flap drive system adjustment.
(a) Put the clamp assembly in its location on the applicable torque tube.
(b) Turn the knob to tighten the clamp assembly on the torque tube.
(c) Turn the rod until it touches the structure to make sure the clamp assembly does not turn.
SUBTASK 27-51-58-020-001
(2) Remove the applicable torque tube guard [10]:
(a) Remove the nuts [9], washers [8] and the bolts [7], bolts [11] or bolts [12] that attach the
torque tube guard [10].
(b) Remove the torque tube guard [10] from the torque tube.
SUBTASK 27-51-58-020-002
(3) Remove the tube assembly [1], tube assembly [2] or tube assembly [3]:
(a) Remove the screws [6] that attach the coupling sleeves [5] to the splined couplings [4].
(b) Move the coupling sleeves [5] off the splined couplings [4].
(c) Remove the tube assembly [1], tube assembly [2] or tube assembly [3].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 402
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Wing Flap Torque Tube Installation
Figure 401 (Sheet 1 of 3)/27-51-58-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 403
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Wing Flap Torque Tube Installation
Figure 401 (Sheet 2 of 3)/27-51-58-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 404
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Wing Flap Torque Tube Installation
Figure 401 (Sheet 3 of 3)/27-51-58-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 405
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Torque Tube Clamp Installation
Figure 402/27-51-58-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-58
Page 406
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-58-400-801
3. Outboard Wing Flap Torque Tube Installation
(Figure 401)
A. General
(1) This task is applicable to the torque tubes outboard of the seal rib angle gearbox.
B. References
Reference Title
12-22-51-640-801 Trailing Edge Flap Torque Tube and Torque Tube Support
Lubrication (P/B 301)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-820-802 Trailing Edge Flap Drive System Adjustment (P/B 501)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
C. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(90)