曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

EFFECTIVITY
GUN ALL 27-51-25
Page 418
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-25-860-004
(3) If the trailing edge flaps are not in the retracted position, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 419
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
OUTBOARD FLAP TRACKS - INSPECTION/CHECK
1. General
A. This procedure contains the task to do an inspection of the flap tracks for the outboard trailing edge
flaps.
TASK 27-51-25-200-801
2. Outboard Flap Outboard Track Inspection
(Figure 601)
A. General
(1) This task gives wear limits for the outboard track on the outboard flap.
(2) this task is applicable to the flap tracks at flap supports No. 1 and 8.
B. References
Reference Title
27-51-25-000-801 Outboard Flap Outboard Track Removal (P/B 401)
27-51-25-400-801 Outboard Flap Outboard Track Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
D. Location Zones
Zone Area
544 Left Wing - Fairing Flap Support No. 1
644 Right Wing - Fairing Flap Support No. 8
E. Procedure
SUBTASK 27-51-25-020-017
(1) Do this task: Outboard Flap Outboard Track Removal, TASK 27-51-25-000-801.
SUBTASK 27-51-25-020-018
(2) Use these tools to do a check for wear on the part of the outboard flap outboard track:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
SUBTASK 27-51-25-020-019
(3) Examine the parts of the outboard flap outboard track (Table 601):
(a) Remove the parts that you will measure.
(b) Measure the parts with a micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096 or a
readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
(c) Compare the dimensions you measured with the permitted wear dimensions.
(d) If the parts are not in tolerance, replace or repair the parts.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 601
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Table 601/27-51-25-993-805
NAME OF THE PARTS
THAT ARE IN CONTACT
DIM.
DIAMETER DESIGN LIMITS WEAR LIMITS
MINIMUM
inches/mm
MAXIMUM
inches/mm
PERMITTED
MAXIMUM I.D./
MINIMUM O.D. OF
WORN PART
MAXIMUM
SERVICE
CLEARANCE
inches/mm
#1 BUSHING I.D. 0.4800 in 0.4896 in 0.4911 in
12.192 mm 12.436 mm 12.474 mm 0.0306 in
#1 FUSE PIN O.D. 0.4600 in 0.4605 in 0.4590 in 0.7772 mm
11.684 mm 11.697 mm 11.659 mm
#2 BUSHING I.D. 0.4700 in 0.4796 in 0.4796 in
11.938 mm 12.182 mm 12.182 mm 0.0196 in
#2 FUSE PIN O.D. 0.4600 in 0.4606 in 0.4600 in 0.4978 mm
11.684 mm 11.699 mm 11.684 mm
#3 BUSHING I.D. 0.5620 in 0.5670 in 0.5670 in
14.275 mm 14.402 mm 14.402 mm 0.0065 in
#3 BOLT O.D. 0.5605 in 0.5615 in 0.5605 in 0.1651 mm
14.237 mm 14.262 mm 14.237 mm
#4 BUSHING I.D. 0.5000 in 0.5050 in 0.5050 in
12.700 mm 12.827 mm 12.827 mm 0.0065 in
#4 BOLT O.D. 0.4985 in 0.4995 in 0.4985 in 0.1651 mm
12.662 mm 12.687 mm 12.662 mm
#5 BUSHING I.D. 0.5620 in 0.5670 in 0.5695 in
14.275 mm 14.402 mm 14.465 mm 0.0700 in
#5 BOLT O.D. 0.4985 in 0.4995 in 0.4970 in 1.7780 mm
12.662 mm 12.687 mm 12.624 mm
#6 BUSHING I.D. 0.5620 in 0.5670 in 0.5695 in
14.275 mm 14.402 mm 14.465 mm 0.0080 in
#6 BOLT O.D. 0.5605 in 0.5615 in 0.5590 in 0.2032 mm
14.237 mm 14.262 mm 14.199 mm
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 602
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-25-420-013
(4) Do this task: Outboard Flap Outboard Track Installation, TASK 27-51-25-400-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 603
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Outboard Track Wear Limits
Figure 601 (Sheet 1 of 2)/27-51-25-990-803
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(23)