曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

fitting [15].
(b) Remove the nuts [24], washers [23], washers [22] and bolts [21] that attach the transmission
assembly [4] to the transmission attach fitting [15].
(c) Carefully lower the transmission assembly [4].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 402
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Transmission Installation
Figure 401 (Sheet 1 of 4)/27-51-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 403
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Transmission Installation
Figure 401 (Sheet 2 of 4)/27-51-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 404
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Transmission Installation
Figure 401 (Sheet 3 of 4)/27-51-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 405
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Inboard Flap Outboard Transmission Installation
Figure 401 (Sheet 4 of 4)/27-51-31-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 406
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-31-400-801
3. Inboard Flap Outboard Transmission Installation
(Figure 401)
A. General
(1) This task is applicable to the transmissions at flap supports No. 3 and 6.
B. References
Reference Title
12-22-51-640-803 Inboard Flap Outboard Ballscrew and Gimbal Lubrication (P/B 301)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-820-802 Trailing Edge Flap Drive System Adjustment (P/B 501)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
27-51-18-400-802 Inboard Flap Support Aft Fairing Installation (P/B 401)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
C. Consumable Materials
Reference Description Specification
C00913 Compound - Nondrying Resin Mix Corrosion
Inhibiting Material
BMS3-27
D00633 Grease - Aircraft General Purpose BMS3-33
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
4 Transmission assembly 27-51-31-10-055 GUN 001-007, 155-157,
201-999
27-51-31-10-060 GUN 001-007, 155-157,
201-999
6 Ballscrew assembly 27-51-32-01-028 GUN 001-007, 121,
155-157, 201-999
E. Location Zones
Zone Area
542 Left Wing - Fairing Flap Support No. 3
553 Left Wing - Inboard Flap
642 Right Wing - Fairing Flap Support No. 6
653 Right Wing - Inboard Flap
F. Inboard Flap Outboard Transmission Installation
SUBTASK 27-51-31-420-001
(1) Install the transmission assembly [4]:
NOTE: The transmission assembly [4] weighs approximately 50 pounds (23 kilograms).
(a) Apply a thin layer of compound, C00913 to the mating surface of the transmission
assembly [4] and the transmission attach fitting [15].
(b) Apply a layer of compound, C00913 to the bolt holes in the transmission assembly [4].
(c) Apply a layer of compound, C00913 to the shank and threads of the bolts [21].
(d) Carefully lift the transmission assembly [4] to its position on the transmission attach fitting
[15].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-31
Page 407
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(e) Install the bolts [21], washers [22], washers [23] and nuts [24] to attach the transmission
assembly [4] to the transmission attach fitting [15].
(f) Tighten the nuts [24] to 500-550 pound-inches (56.5-62.1 newton-meters) more than the runon
torque.
SUBTASK 27-51-31-420-002
(2) Connect the ballscrew assembly [6] to the yoke [16] on the transmission assembly [4]:
(a) Turn the ballscrew nut [28] until it is at the forward end of the ballscrew assembly [6].
(b) Apply a layer of grease, D00633 to the mating surfaces of the yoke [16] and the ballscrew
assembly [6].
(c) Put the ballscrew assembly [6] into the yoke [16].
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(45)