曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

repeatable.
SUBTASK 27-51-42-960-003
(3) If the backlash is more than 0.0073 inch (0.185 millimeter), then replace the ballscrew assembly.
These are the tasks:
Outboard Flap Inboard Ballscrew and Gimbal Removal, TASK 27-51-42-000-802,
Outboard Flap Inboard Ballscrew and Gimbal Installation, TASK 27-51-42-400-802.
SUBTASK 27-51-42-080-003
(4) Remove the dial indicator assembly from the ballscrew.
SUBTASK 27-51-42-440-006
(5) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
SUBTASK 27-51-42-860-016
(6) Retract the trailing edge flaps to the retracted position, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
G. Outboard Flap Inboard Ballscrew Backlash Check With the Lever and Clamp Tool
NOTE: With this method, you use the lever and clamp tool to apply the load to the ballscrew nut.
SUBTASK 27-51-42-010-004
(1) Do this task: Outboard Flap Inboard Support Aft Fairing Removal, TASK 27-51-28-000-804.
SUBTASK 27-51-42-860-017
(2) Retract the trailing edge flaps to the 15-unit position, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
SUBTASK 27-51-42-040-006
(3) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-51-42-480-005
(4) Install the lever and clamp tool on the ballscrew:
NOTE: The lever and clamp tool is a part of the tester, SPL-1753.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-42
Page 608
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Put the lever and clamp tool in its position on the ballscrew aft of the ballscrew nut.
NOTE: Make sure the load surfaces of the lever and clamp tool touch the aft side of the
ballscrew nut.
(b) Tighten the clamp-up bolt to 200-300 pound-inches (22.6-33.8 newton-meters).
NOTE: Make sure the handles of the lever and clamp tool are in the relaxed position.
SUBTASK 27-51-42-480-006
(5) Install the dial indicator assembly on the ballscrew:
NOTE: The dial indicator assembly is a part of the tester, SPL-1753.
(a) Put the dial indicator assembly on the ballscrew.
NOTE: Make sure the pointer touches the forward end of the ballscrew nut.
(b) Put the strap around the ballscrew to help hold the dial indicator assembly on the
ballscrew.
(c) Adjust the dial indicator to zero.
SUBTASK 27-51-42-220-004
(6) Measure the backlash of the ballscrew and ballscrew nut:
(a) Move the handles of the lever and clamp tool together until the dial indicator stops.
NOTE: This will apply a load to the ballscrew nut, and move it forward on the ballscrew.
(b) Use the dial indicator to measure the movement of the ballscrew nut.
NOTE: The movement of the ballscrew nut is the backlash.
(c) Do these steps a total of five times to make sure the movement of the dial indicator is
repeatable.
SUBTASK 27-51-42-960-004
(7) If the backlash is more than 0.0073 inch (0.185 millimeter), then replace the ballscrew assembly.
These are the tasks:
Outboard Flap Inboard Ballscrew and Gimbal Removal, TASK 27-51-42-000-802,
Outboard Flap Inboard Ballscrew and Gimbal Installation, TASK 27-51-42-400-802.
SUBTASK 27-51-42-080-004
(8) Remove the dial indicator assembly and the lever and clamp tool from the ballscrew.
SUBTASK 27-51-42-410-004
(9) Do this task: Outboard Flap Inboard Support Aft Fairing Installation, TASK 27-51-28-400-804.
SUBTASK 27-51-42-440-007
(10) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
SUBTASK 27-51-42-860-018
(11) Retract the trailing edge flaps to the retracted position, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-42
Page 609
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
FLAP POWER DRIVE UNIT (PDU) - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the flap power drive unit (PDU)
(2) An installation of the flap power drive unit (PDU)
(3) A replacement of the shearout for the manual drive on the flap power drive unit (PDU).
(4) A removal of the hydraulic and electric motor seals from the flap power drive unit (PDU).
(5) An installation of the hydraulic and electric motor seals from the flap power drive unit (PDU).
TASK 27-51-51-000-801
2. Flap Power Drive Unit (PDU) Removal
(Figure 401)
A. General
(1) You can remove and install the flap power drive unit with the hydraulic and electric motors either
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(72)