曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

TASK 27-51-28-400-802.
(b) Do this task: Outboard Flap Outboard Support Forward Fairing Installation,
TASK 27-51-28-400-801.
SUBTASK 27-51-25-440-001
(2) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 409
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-51-25-860-002
(3) If the trailing edge flaps are not in the retracted position, do this task: Retract the Trailing Edge
Flaps, TASK 27-51-00-860-804.
------------------------- END OF TASK ---------------------------
TASK 27-51-25-000-802
4. Outboard Flap Inboard Track Removal
(Figure 402)
A. General
(1) This task is applicable to the flap tracks at flap supports No. 2 and 7.
B. References
Reference Title
27-51-00-040-801 Trailing Edge Flap System Deactivation (P/B 201)
27-51-00-860-803 Extend the Trailing Edge Flaps (P/B 201)
27-51-21-000-801 Outboard Trailing Edge Flap Removal (P/B 401)
27-51-28-000-803 Outboard Flap Inboard Support Forward Fairing Removal (P/B 401)
27-51-28-000-804 Outboard Flap Inboard Support Aft Fairing Removal (P/B 401)
27-51-41-000-802 Outboard Flap Inboard Transmission Removal (P/B 401)
27-59-02-000-802 Outboard Flap Inboard Skew Mechanism Removal (P/B 201)
C. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
COM-1568 Jack - Hydraulic, General Low Profile
(Part #: B67563, Supplier: 36251, A/P Effectivity: 737-ALL)
(Part #: HW93718, Supplier: 28047, A/P Effectivity: 737-ALL)
(Opt Part #: W93718, Supplier: 36251, A/P Effectivity: 737-ALL)
SPL-1733 Adapter - Hoist, Removal/Installation, Flap Track
(Part #: C27040-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
D. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
643 Right Wing - Fairing Flap Support No. 7
E. Prepare for the Removal
SUBTASK 27-51-25-860-003
(1) Extend the trailing edge flaps to the 40-unit position. To extend them, do this task: Extend the
Trailing Edge Flaps, TASK 27-51-00-860-803.
SUBTASK 27-51-25-040-002
(2) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-51-25-010-002
(3) Remove the fairings for the inboard track on the outboard flap:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 410
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Do this task: Outboard Flap Inboard Support Forward Fairing Removal,
TASK 27-51-28-000-803.
(b) Do this task: Outboard Flap Inboard Support Aft Fairing Removal,
TASK 27-51-28-000-804.
SUBTASK 27-51-25-020-009
(4) Do this task: Outboard Trailing Edge Flap Removal, TASK 27-51-21-000-801.
SUBTASK 27-51-25-020-010
(5) Do this task: Outboard Flap Inboard Skew Mechanism Removal, TASK 27-59-02-000-802.
SUBTASK 27-51-25-020-011
(6) Do this task: Outboard Flap Inboard Transmission Removal, TASK 27-51-41-000-802.
F. Outboard Flap Inboard Track Removal
NOTE: Make sure you support the flap track while you disconnect it.
SUBTASK 27-51-25-480-004
(1) If you will use the adapter, SPL-1733, install it on the flap track [41]:
(a) Install the adapter, SPL-1733 on the flap track [41] approximately 33 inches (84 cm) aft of the
track attach fitting.
(b) Put a low profile hydraulic jack, COM-1568 below the adapter, SPL-1733 to support the flap
track [41].
SUBTASK 27-51-25-020-012
(2) Remove the nut [56], washer [55], washer [54], washer [53] and bolt [52] to disconnect the
jumper wire [57] from the flap track [41].
SUBTASK 27-51-25-020-013
(3) Disconnect the forward end of the flap track [41]:
(a) Remove the bolts [59] and washers [58] that attach the failsafe fitting assembly [60] to the
track attach fitting.
(b) Remove the nut [63], washer [62] and fuse pin [61] from the forward end of the flap
track [41].
SUBTASK 27-51-25-020-014
(4) Disconnect the aft end of the flap track [41] from the structure:
(a) Remove the nut [46], washer [45], washer [44] and bolt [43] that attach the outboard side of
the flap track [41] to the structure.
(b) Remove the nut [47], washer [48], washer [50] and bolt [51] that attach the inboard side of
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(20)